BTRFS-CONVERT(8)                        Btrfs Manual                        BTRFS-CONVERT(8)

NAME
       btrfs-convert - convert from ext2/3/4 or reiserfs filesystem to btrfs in-place

SYNOPSIS
       btrfs-convert [options] <device>

DESCRIPTION
       btrfs-convert is used to convert existing source filesystem image to a btrfs
       filesystem in-place. The original filesystem image is accessible in subvolume named
       like ext2_saved as file image.

       Supported filesystems:

       •   ext2, ext3, ext4 — original feature, always built in

       •   reiserfs — since version 4.13, optionally built, requires libreiserfscore 3.6.27

       The list of supported source filesystem by a given binary is listed at the end of
       help (option --help).

           Warning
           If you are going to perform rollback to the original filesystem, you should not
           execute btrfs balance command on the converted filesystem. This will change the
           extent layout and make btrfs-convert unable to rollback.

       The conversion utilizes free space of the original filesystem. The exact estimate of
       the required space cannot be foretold. The final btrfs metadata might occupy several
       gigabytes on a hundreds-gigabyte filesystem.

       If the ability to rollback is no longer important, the it is recommended to perform a
       few more steps to transition the btrfs filesystem to a more compact layout. This is
       because the conversion inherits the original data blocks' fragmentation, and also
       because the metadata blocks are bound to the original free space layout.

       Due to different constraints, it is only possible to convert filesystems that have a
       supported data block size (ie. the same that would be valid for mkfs.btrfs). This is
       typically the system page size (4KiB on x86_64 machines).

           Note
           The source filesystem should be clean, you are encouraged to run the fsck tool if
           you’re not sure.

       REMOVE THE ORIGINAL FILESYSTEM METADATA

       By removing the subvolume named like ext2_saved or reiserfs_saved, all metadata of
       the original filesystem will be removed:

           # btrfs subvolume delete /mnt/ext2_saved

       At this point it is not possible to do a rollback. The filesystem is usable but may
       be impacted by the fragmentation inherited from the original filesystem.

       MAKE FILE DATA MORE CONTIGUOUS

       An optional but recommended step is to run defragmentation on the entire filesystem.
       This will attempt to make file extents more contiguous.

           # btrfs filesystem defrag -v -r -f -t 32M /mnt/btrfs

       Verbose recursive defragmentation (-v, -r), flush data per-file (-f) with target
       extent size 32MiB (-t).

       ATTEMPT TO MAKE BTRFS METADATA MORE COMPACT

       Optional but recommended step.

       The metadata block groups after conversion may be smaller than the default size
       (256MiB or 1GiB). Running a balance will attempt to merge the block groups. This
       depends on the free space layout (and fragmentation) and may fail due to lack of
       enough work space. This is a soft error leaving the filesystem usable but the block
       group layout may remain unchanged.

       Note that balance operation takes a lot of time, please see also btrfs-balance(8).

           # btrfs balance start -m /mnt/btrfs

OPTIONS
       -d|--no-datasum
           disable data checksum calculations and set the NODATASUM file flag, this can
           speed up the conversion

       -i|--no-xattr
           ignore xattrs and ACLs of files

       -n|--no-inline
           disable inlining of small files to metadata blocks, this will decrease the
           metadata consumption and may help to convert a filesystem with low free space

       -N|--nodesize <SIZE>
           set filesystem nodesize, the tree block size in which btrfs stores its metadata.
           The default value is 16KB (16384) or the page size, whichever is bigger. Must be
           a multiple of the sectorsize, but not larger than 65536. See mkfs.btrfs(8) for
           more details.

       -r|--rollback
           rollback to the original ext2/3/4 filesystem if possible

       -l|--label <LABEL>
           set filesystem label during conversion

       -L|--copy-label
           use label from the converted filesystem

       -O|--features <feature1>[,<feature2>...]
           A list of filesystem features enabled the at time of conversion. Not all features
           are supported by old kernels. To disable a feature, prefix it with ^. Description
           of the features is in section FILESYSTEM FEATURES of mkfs.btrfs(8).

           To see all available features that btrfs-convert supports run:

           btrfs-convert -O list-all

       -p|--progress
           show progress of conversion (a heartbeat indicator and number of inodes
           processed), on by default

       --no-progress
           disable progress and show only the main phases of conversion

EXIT STATUS
       btrfs-convert will return 0 if no error happened. If any problems happened, 1 will be
       returned.

SEE ALSO
       mkfs.btrfs(8)

Btrfs v4.20.1                            01/23/2019                         BTRFS-CONVERT(8)

usage: btrfs-convert [options] device
options:
        -d|--no-datasum        disable data checksum, sets NODATASUM
        -i|--no-xattr          ignore xattrs and ACLs
        -n|--no-inline         disable inlining of small files to metadata
        -N|--nodesize SIZE     set filesystem metadata nodesize
        -r|--rollback          roll back to the original filesystem
        -l|--label LABEL       set filesystem label
        -L|--copy-label        use label from converted filesystem
        -p|--progress          show converting progress (default)
        -O|--features LIST     comma separated list of filesystem features
        --no-progress          show only overview, not the detailed progress

Suported filesystems:
        ext2/3/4: yes